供应

德国GT-550脉冲式探测器是一款抗高压，大深度脉冲式金属探测器，主用于宝藏、遗址、考古。探测深度可达十米，一个30公分法人铜片现场实际探测达3.5米。

产品用途：考古、探宝、金、银、铜等。






GT550是一款采用德国KTS技术原装芯片，大深度脉冲机，它比传统的脉冲机器更深更稳定，抗高压。且操作方法特别简单。
操作方法：开关：开机旋钮和音量大小功率：机器功率大小调节 功率越大深度越大 反之越小（具体深度需要灵敏度和复位按钮来配合调节）
高压档位：（深度好但是受到的干扰也越大）
普通档位： 适合干扰严重和有矿化的地方使用，但是深度不如高压挡具体使用档位根据实地干扰和土质决定（如遇高压线打到此档位）
Sing:信号指示.led灯与显示屏信号同步 探测到金属红灯亮
频率：辅助机器旋钮也叫敏感度 一般调节到一秒响二三下为宜
灵敏度：深度控制旋钮 调节到比敏感度快一点点 探测时始终保持此状态（深度才会好）
 Phones:耳机插孔 插上耳机 外音自动断开



注意事项：机器操作时 保持关机状态  插上线圈然后开机  测试效果可以线圈放在地面 实际操作时需要保持线圈离地面30厘米高度调节机器 然后进行探测，探测深度根据被测物体大小深度不同。30公分小线圈盘以一个铜钱为例 深度50公分。1米框以30公分金属为例  2-2.5米（实埋）2米框以30公分金属为例  3-3.5米(实埋)被测物体越大线圈框越大探测深度越深。
功率300W  
电池16.8V  
6000毫安
频率600Hz




产品特点：
1.探测深度： 12米
2.探测范围大：搜索完1个足球场只需40分钟
3.地平衡比较稳定：探测时不受矿化反应和盐类物质的影响

4.它配备多种搜索线圈，可适应各种不同探测需要

The German GT-550 pulse detector is a high-voltage resistant, large-depth pulsed metal detector, mainly used for treasures, ruins, and archaeology. The detection depth can reach ten meters, and the actual detection of a 30 cm corporate copper sheet on site can reach 3.5 meters.
Product use: archaeology, treasure hunting, gold, silver, copper, etc.
GT550 is a large depth pulse machine with original German KTS technology. It is deeper and more stable than traditional pulse machines, and is resistant to high voltage. And the operation method is particularly simple.
Operation method: switch: turn on the knob and volume power: adjust the power of the machine, the greater the power, the greater the depth, the smaller it is (the specific depth requires sensitivity and reset buttons to adjust)
High pressure gear: (the depth is good but the interference is greater)
Ordinary gear: suitable for use in places with severe interference and mineralization, but the depth is not as good as the high-voltage gear. The specific gear used is determined according to the field interference and soil quality (if high-voltage lines hit this gear)
Sing: Signal indication. The led light is synchronized with the display signal, the red light is on when the metal is detected
Frequency: The auxiliary machine knob is also called sensitivity. It is generally appropriate to adjust to two or three times per second.
Sensitivity: The depth control knob is adjusted to be a little faster than the sensitivity. Always maintain this state during detection (the depth will be good)