产品

我们店铺的切割机种类有很多，动力有柴油，汽油，电动的，有单用的，还有切割刻纹一体机，有普通款的，还有威克款的，质量方面您大可放心，重点是看哪款动力适合您，外观看您喜欢什么样式的！

There are many kinds of cutting machines in our shop, such as diesel, gasoline, electric, single-use, and all-in-one cutting and engraving machines, including ordinary ones and wick ones, you can rest assured in terms of quality, the focus is to see which type of power suits you, look at what style you like!
我们做出来的原则就是结构简单，操作灵活，让您爱不释手！
We made the principle is simple structure, flexible operation, let you Hands All Over!

混凝土切割机产品用途：
专为市政建设改选、路面维修施工、机场路面切割、通讯工程埋设及地板、车道等现场作业专业切割。?主要用于切割混凝土，水泥，地板及石制路面，切割路面收缩缝或破损路面。是使用金刚石锯片切割混凝土路面、大理石板、水磨构件等脆性材质的锯切工具。
For municipal construction re-election, road maintenance and construction, airport road cutting, communications engineering buried and floors, driveways and other field operations professional cutting. It is mainly used for cutting concrete, cement, floor and stone pavement, cutting pavement contraction joints or broken pavement. Diamond Blade is a sawing tool for cutting brittle materials such as concrete pavements, marble slabs, and water mill components.


水冷柴油切割机参数：
机器型号：500型
锯片直径 ：400-500mm
较大切深 ：180mm
锯片线速度：36-45m/s
水箱 ：37L
包装尺寸：1500?500?900mm
重量：260KG
这款500款的我们采用15马力的水冷柴油机，强劲有力
水箱采用的也是加厚的，橡胶手把耐磨，手柄轮可控制锯片的切割哦，好方便的一款！
移动方便，减少了扯电缆线的麻烦！
性能稳定，不用担心，直接下单!

Section 500 we use 15 horsepower water-cooled diesel engine, strong water tank is also thick, rubber handlebar wear-resistant, handle wheel can control the cutting blade Oh, a good convenience! Easy to move, reduce the trouble of pulling cable! Stable performance, do not worry, direct order!

l混凝土切割机使用方法：
1、开机前应检查各部分螺栓，螺母有无松动；检查电源、接线有无漏电现象；锯片旋转方向与防护罩标注方向是否一致，检查无误后方可开机工作。
?2、开机工作前，水箱应注满水；工作时，应及时拧开水管开关，向锯片喷水冷却。
3、切割深度由手轮调节，用手轮转动推把前面的手轮，使螺杆丝母旋转升降，于是前轮高低位置改变，锯片随之升高或下落。
?4、切割前，锯片应离开地面，锯片正常运转后，应慢慢旋转手轮使机头下落，当锯片切刀予定深度后，即可向前推进，此时，导向杆应先放下，使导向轮着地。
5、切割行进时，双目应注视导向轮以掌握切缝方向，双手推动推把，使导向轮沿予定的切割线前进，保证切口的平直性。
?6、由于行进过速切割过深或遇到硬物质时，电机因过载使锯片转速下降，此时应停止推进或减慢送进速度，以保护电机、柴油机、汽油机和锯片不受损坏。
来砸单吧，朋友们，使劲砸单，热烈欢迎！
Concrete cutting machine use method: 1, before starting the machine should check all parts of bolts, nuts loose; check the power supply, wiring leakage phenomenon; saw blade rotation direction and protective cover marked direction is consistent, do not start the machine until it has been checked correctly. 2. Before starting the machine, the water tank should be filled with water; while working, the water pipe switch should be turned on in time to spray water to the saw blade for cooling. 3, cutting depth by hand wheel adjustment, with hand wheel rotation push the hand wheel in front, screw nut rotation up and down, so that the front wheel high and low position change, the saw blade then up or down. 4, before cutting, the saw blade should leave the ground, after the saw blade normal operation, should slowly rotate the handwheel to make the machine head fall, when the saw blade blade to be given a certain depth, can advance, at this time, the guide rod should first put down, so that the guide wheel landing. 5. When cutting, both eyes should look at the guide wheel to grasp the direction of the cutting seam, and both hands should push the handle to make the guide wheel advance along the fixed cutting line to ensure the straightness of the incision. 6, because of moving too fast cutting too deep or encountered hard material, the motor due to overload to reduce the blade speed, at this time should stop or slow down the feed speed, to protect the motor, diesel engine, gasoline engine and saw blade from damage. HIT IT, folks! HIT IT HARD! GIVE IT UP!

联系人：陈经理
地址：山东省济宁市任城区金宇路4号
手机：13165175381