供应

摩擦磨损试验机厂家

摩擦磨损试验机厂家  功能特点：

1、试样尺寸： 30mm?7mm?6mm

2、转动速度： 0-500转/分 （可调）

3、负 荷： 196N ? 0.1%（可增至392N）

4、摩擦环尺寸：￠40?10mm ，倒角0.5?45?，外圆表面与内圆同心度偏差小于0.01

5、摩擦环材质：45号钢,淬火,热处理HRC40-45,外圆表面光洁度▼8

6、摩擦力矩： 0--4N?m

7、砝码重量：4KG砝码一件，1KG砝码4件，可实现重量叠加功能。

Functional characteristics:

1, sample size: 30mm x 7mm x 6mm

2, rotation speed: 0-500 turn / points (adjustable)

3, load: 196N 0.1% (can be increased to 392N)

4, the size of the friction ring is: 40 x 10mm, chamfer 0.5 * 45 degrees, and the concentricity deviation between the outer surface and the inner circle is less than 0.01.

5, friction ring material: 45 steel, quenching, heat treatment HRC40-45, round surface finish 8

6, friction moment: 0--4N. M

7, weight weight: 4KG weight one, 1KG weight 4, can achieve weight superposition function.

试验报告

试验报告应包括下列内容：

A.塑料名称、规格、牌号、生产厂；

B.试样的制备方法，摩擦表面状况，测定的试样个数；

C.环境温度、温度及状态调节条件；

D.圆环材质、硬度、光洁度和外径尺寸；

E.试验负荷；

F.试验结果：磨痕宽度或体积磨损及摩擦系数的测定结果；

G.试验日期、人员。

Test report

The test report should include the following contents:

A. Plastic name, specification, brand, and manufacturer;

B. The preparation method of the sample, the condition of the friction surface, and the number of samples measured;

C. Environmental temperature, temperature and state regulation conditions;

D. Circular ring material, hardness, smoothness, and outer diameter size;

E. Test load;

F. Test results: Measurement results of abrasion width or volume wear and friction coefficient;

G. Test date and personnel.

精度Precision:

1、速度精度：1%

2、负荷精度：0.5%

3、摩擦力矩精度：1%

4、计数器精度：1S

5、传感器测量精度：1% FS

Precision:

1. Speed precision: 1%

2. Load precision: 0.5%

3. The precision of friction moment: 1%

4. Counter precision: 1S

5. Sensor measurement accuracy: 1% FS

功能：

本厂生产的计算机控制塑料滑动摩擦试验机是在现有电子塑料滑动摩擦试验机的基础上又增加了很多试验功能，可以同时显示扭矩-时间曲线，随意设定试验次数，显示当前试验次数，设定时间及当前试验时间等多种功能，本机还配有彩色打印机，可以打印出带有曲线，表格数据，试验单位名头的精美的试验报告单。

Function:

The computer controlled plastic sliding friction test machine produced by our factory is on the basis of the existing electronic plastic sliding friction test machine, and has added a lot of test functions. It can display the torque time curve at the same time, set the test times at will, display the current test times, set the time and the current test time and other functions, this machine is this machine. It also has a color printer, which can print out exquisite test reports with curves, table data and test units.

试验步骤

1、圆环应清除油污，贮存于干燥缸内以防生锈。

2、试样经状态调节后用感量为0.1毫克的分析天平称取其质量（M1）。

3、把试样装进夹具，摩擦面用角尺校正并使它与圆环的交线外于试样正中。装好摩擦力矩记录纸，开机校好零点。

4、再次用乙醇、丙酮等不与塑料起作用的溶剂仔细清除试样和圆环上的油污，此后不准再用手接触试样和圆环的表面。

5、平稳地加荷至选定的负荷值。

6、对磨2小时后停机卸负荷，取下试样和圆环，清理试样表面后，用精度不低于0.02毫米的量具测量磨痕宽度，或在试验环境下存放1小时后称取试样质量（m2)。

7、读取摩擦力矩值。

Experimental steps

1. The circular ring should be cleaned of oil stains and stored in a drying cylinder to prevent rusting.

2. After adjusting the state of the sample, weigh its mass (M1) using an analytical balance with a sensitivity of 0.1 milligrams.

3. Insert the sample into the fixture, calibrate the friction surface with an angle ruler, and ensure that its intersection with the circular ring is outside the center of the sample. Install the friction torque recording paper and start the machine to calibrate the zero point.

4. Carefully remove the oil stains on the sample and the ring using solvents such as ethanol and acetone that do not work with plastic. After that, do not touch the surface of the sample and ring with your hands.

5. Smoothly load to the selected load value.

6. After grinding for 2 hours, stop the machine to unload the load, remove the sample and ring, clean the surface of the sample, measure the width of the grinding mark with a measuring tool with an accuracy of not less than 0.02 millimeters, or weigh the sample mass (m2) after storing it in the test environment for 1 hour.

7. Read the torque value of friction force.

状态调节

状态调节按GB2918-82《塑料试样状态调节和试验的标准环境》进行，温度为23?5摄氏度，温度为50?10%。

摩擦磨损定义

1、摩擦：两物体接触表面间产生阻碍切向相对移动的现象称为摩擦。

2、滑动摩擦：两接触物体接触点具有不同速度时之摩擦。

3、摩擦力：两物体摩擦时相对移动的阻力。

4、摩擦系数：阻碍两物体相对运动的摩擦力对作用到物体表面的法向力之比。

5、磨损：物体相对运动时相互接触表面的物质不断损失或产生残余变形称为磨损。

Definition of Friction and Wear

1. Friction: The phenomenon of hindering tangential relative movement between two surfaces in contact is called friction.

2. Sliding friction: Friction between two objects in contact at different speeds.

3. Friction: The resistance to relative movement between two objects when they rub against each other.

4. Friction coefficient: The ratio of the frictional force that impedes the relative motion of two objects to the normal force acting on the surface of the object.

5. Wear: The continuous loss or residual deformation of substances on the surfaces in contact with each other during relative motion of objects is called wear.

主要配置及附件：（计算机控制）

1、试验主机一台

2、高精度扭矩传感器一只

3、计算机数据采集卡一块

4、计算机一台（品牌）

5、彩色激光喷墨打印机一台

6、计算机控制软件一套

7、4Kg 砝码两件（备用一套）

8、标准磨擦环四件（备用两件）

9、产品使用说明书一份

10、产品合格证

11、产品装箱单一份

12、整机重量：约87 公斤

Main configuration and accessories: (computer control)

1. A test host

2. A high precision torque sensor

3. One piece of computer data acquisition card

4. One computer (brand)

5. A color laser inkjet printer

6. A set of computer control software

7, two 4Kg weights (a spare set)

8, four standard friction ring (two spare)

9. One copy of the product instructions

10. Product qualification certificate

11. Packing a single part of the product

12, the weight of the whole machine: about 87 kilograms

售后服务。

1、保修期内非人为损坏的零部件免费更换，保修期内接到用户邀请后，最迟响应时间为4小时内，在与用户确认故障后，我公司会在48小时内派工程师到达现场进行免费服务，尽快查清故障所在位置和故障原因，并向用户及时报告故障的原因和排除办法。

2、提供实时的远程诊断和维护服务。

3、每年进行客户回访。

4、保修期外继续为用户提供优质技术服务，在接到用户维修邀请后2天内派工程师到达用户现场进行维修。并享有优惠购买零配件的待遇。

5、保修期内人为损坏的零部件按采购（加工）价格收费更换。

6、软件升级：终生免费提供新版本控制软件。

7、安装及调试合格后，自客户签字认可之日起，我方对于提供的产品免费保修三年。保修期满后，我方将继续跟踪服务，客户享受终生维修，负责及时提供必要的售后服务、技术咨询。

8、产品交货期：尽量按用户要求，若有特殊要求，需提前完工的，我公司可特别组织生产、安装，力争满足用户需求。

9、保修承诺：我司对本次协议供货有效期内所提供的所有产品保质期 ，有效期内所提供的产品，提供正常工作日全天侯服务，终身技术服务支持。

10、响应时间：保修期内，产品若发生故障，在接到贵公司报修后，24小时内帮客户解决问题。

11、服务体系：作为设备供应商本公司对本次招标所提供的产品提供保障体系： 当设备出现故障，必要时将派指定的专业技术员在规定时间内上门维修或寄修，产生的运费由本公司承担。

12、产品价格承诺 1、在同等竞争条件下，我公司在不以降低产品技术性能、更改产品部件为代价的基础上，真诚以最优惠的价格提供给贵方。 2、在保修期内供方将免费维修和更换属质量原因造成的零部件损坏，保修期外零部件的损坏，提供的配件只收成本费，由需方人为因素造成的设备损坏，供方维修或提供的配件均按成本价计。

13、售后服务保证

公司实力保障：本公司有完善的售后服务体系;

功能特点：

1、试样尺寸： 30mm?7mm?6mm

2、转动速度： 0-500转/分 （可调）

3、负 荷： 196N ? 0.1%（可增至392N）

4、摩擦环尺寸：￠40?10mm ，倒角0.5?45?，外圆表面与内圆同心度偏差小于0.01

5、摩擦环材质：45号钢,淬火,热处理HRC40-45,外圆表面光洁度▼8

6、摩擦力矩： 0--4N?m

7、砝码重量：4KG砝码一件，1KG砝码4件，可实现重量叠加功能。

Functional characteristics:

1, sample size: 30mm x 7mm x 6mm

2, rotation speed: 0-500 turn / points (adjustable)

3, load: 196N 0.1% (can be increased to 392N)

4, the size of the friction ring is: 40 x 10mm, chamfer 0.5 * 45 degrees, and the concentricity deviation between the outer surface and the inner circle is less than 0.01.

5, friction ring material: 45 steel, quenching, heat treatment HRC40-45, round surface finish 8

6, friction moment: 0--4N. M

7, weight weight: 4KG weight one, 1KG weight 4, can achieve weight superposition function.

试验报告

试验报告应包括下列内容：

A.塑料名称、规格、牌号、生产厂；

B.试样的制备方法，摩擦表面状况，测定的试样个数；

C.环境温度、温度及状态调节条件；

D.圆环材质、硬度、光洁度和外径尺寸；

E.试验负荷；

F.试验结果：磨痕宽度或体积磨损及摩擦系数的测定结果；

G.试验日期、人员。

Test report

The test report should include the following contents:

A. Plastic name, specification, brand, and manufacturer;

B. The preparation method of the sample, the condition of the friction surface, and the number of samples measured;

C. Environmental temperature, temperature and state regulation conditions;

D. Circular ring material, hardness, smoothness, and outer diameter size;

E. Test load;

F. Test results: Measurement results of abrasion width or volume wear and friction coefficient;

G. Test date and personnel.

精度Precision:

1、速度精度：1%

2、负荷精度：0.5%

3、摩擦力矩精度：1%

4、计数器精度：1S

5、传感器测量精度：1% FS

Precision:

1. Speed precision: 1%

2. Load precision: 0.5%

3. The precision of friction moment: 1%

4. Counter precision: 1S

5. Sensor measurement accuracy: 1% FS

功能：

本厂生产的计算机控制塑料滑动摩擦试验机是在现有电子塑料滑动摩擦试验机的基础上又增加了很多试验功能，可以同时显示扭矩-时间曲线，随意设定试验次数，显示当前试验次数，设定时间及当前试验时间等多种功能，本机还配有彩色打印机，可以打印出带有曲线，表格数据，试验单位名头的精美的试验报告单。

Function:

The computer controlled plastic sliding friction test machine produced by our factory is on the basis of the existing electronic plastic sliding friction test machine, and has added a lot of test functions. It can display the torque time curve at the same time, set the test times at will, display the current test times, set the time and the current test time and other functions, this machine is this machine. It also has a color printer, which can print out exquisite test reports with curves, table data and test units.

试验步骤

1、圆环应清除油污，贮存于干燥缸内以防生锈。

2、试样经状态调节后用感量为0.1毫克的分析天平称取其质量（M1）。

3、把试样装进夹具，摩擦面用角尺校正并使它与圆环的交线外于试样正中。装好摩擦力矩记录纸，开机校好零点。

4、再次用乙醇、丙酮等不与塑料起作用的溶剂仔细清除试样和圆环上的油污，此后不准再用手接触试样和圆环的表面。

5、平稳地加荷至选定的负荷值。

6、对磨2小时后停机卸负荷，取下试样和圆环，清理试样表面后，用精度不低于0.02毫米的量具测量磨痕宽度，或在试验环境下存放1小时后称取试样质量（m2)。

7、读取摩擦力矩值。

Experimental steps

1. The circular ring should be cleaned of oil stains and stored in a drying cylinder to prevent rusting.

2. After adjusting the state of the sample, weigh its mass (M1) using an analytical balance with a sensitivity of 0.1 milligrams.

3. Insert the sample into the fixture, calibrate the friction surface with an angle ruler, and ensure that its intersection with the circular ring is outside the center of the sample. Install the friction torque recording paper and start the machine to calibrate the zero point.

4. Carefully remove the oil stains on the sample and the ring using solvents such as ethanol and acetone that do not work with plastic. After that, do not touch the surface of the sample and ring with your hands.

5. Smoothly load to the selected load value.

6. After grinding for 2 hours, stop the machine to unload the load, remove the sample and ring, clean the surface of the sample, measure the width of the grinding mark with a measuring tool with an accuracy of not less than 0.02 millimeters, or weigh the sample mass (m2) after storing it in the test environment for 1 hour.

7. Read the torque value of friction force.

状态调节

状态调节按GB2918-82《塑料试样状态调节和试验的标准环境》进行，温度为23?5摄氏度，温度为50?10%。

摩擦磨损定义

1、摩擦：两物体接触表面间产生阻碍切向相对移动的现象称为摩擦。

2、滑动摩擦：两接触物体接触点具有不同速度时之摩擦。

3、摩擦力：两物体摩擦时相对移动的阻力。

4、摩擦系数：阻碍两物体相对运动的摩擦力对作用到物体表面的法向力之比。

5、磨损：物体相对运动时相互接触表面的物质不断损失或产生残余变形称为磨损。

Definition of Friction and Wear

1. Friction: The phenomenon of hindering tangential relative movement between two surfaces in contact is called friction.

2. Sliding friction: Friction between two objects in contact at different speeds.

3. Friction: The resistance to relative movement between two objects when they rub against each other.

4. Friction coefficient: The ratio of the frictional force that impedes the relative motion of two objects to the normal force acting on the surface of the object.

5. Wear: The continuous loss or residual deformation of substances on the surfaces in contact with each other during relative motion of objects is called wear.

主要配置及附件：（计算机控制）

1、试验主机一台

2、高精度扭矩传感器一只

3、计算机数据采集卡一块

4、计算机一台（品牌）

5、彩色激光喷墨打印机一台

6、计算机控制软件一套

7、4Kg 砝码两件（备用一套）

8、标准磨擦环四件（备用两件）

9、产品使用说明书一份

10、产品合格证

11、产品装箱单一份

12、整机重量：约87 公斤

Main configuration and accessories: (computer control)

1. A test host

2. A high precision torque sensor

3. One piece of computer data acquisition card

4. One computer (brand)

5. A color laser inkjet printer

6. A set of computer control software

7, two 4Kg weights (a spare set)

8, four standard friction ring (two spare)

9. One copy of the product instructions

10. Product qualification certificate

11. Packing a single part of the product

12, the weight of the whole machine: about 87 kilograms

售后服务。

1、保修期内非人为损坏的零部件免费更换，保修期内接到用户邀请后，最迟响应时间为4小时内，在与用户确认故障后，我公司会在48小时内派工程师到达现场进行免费服务，尽快查清故障所在位置和故障原因，并向用户及时报告故障的原因和排除办法。

2、提供实时的远程诊断和维护服务。

3、每年进行客户回访。

4、保修期外继续为用户提供优质技术服务，在接到用户维修邀请后2天内派工程师到达用户现场进行维修。并享有优惠购买零配件的待遇。

5、保修期内人为损坏的零部件按采购（加工）价格收费更换。

6、软件升级：终生免费提供新版本控制软件。

7、安装及调试合格后，自客户签字认可之日起，我方对于提供的产品免费保修三年。保修期满后，我方将继续跟踪服务，客户享受终生维修，负责及时提供必要的售后服务、技术咨询。

8、产品交货期：尽量按用户要求，若有特殊要求，需提前完工的，我公司可特别组织生产、安装，力争满足用户需求。

9、保修承诺：我司对本次协议供货有效期内所提供的所有产品保质期 ，有效期内所提供的产品，提供正常工作日全天侯服务，终身技术服务支持。

10、响应时间：保修期内，产品若发生故障，在接到贵公司报修后，24小时内帮客户解决问题。

11、服务体系：作为设备供应商本公司对本次招标所提供的产品提供保障体系： 当设备出现故障，必要时将派指定的专业技术员在规定时间内上门维修或寄修，产生的运费由本公司承担。

12、产品价格承诺 1、在同等竞争条件下，我公司在不以降低产品技术性能、更改产品部件为代价的基础上，真诚以最优惠的价格提供给贵方。 2、在保修期内供方将免费维修和更换属质量原因造成的零部件损坏，保修期外零部件的损坏，提供的配件只收成本费，由需方人为因素造成的设备损坏，供方维修或提供的配件均按成本价计。

13、售后服务保证

公司实力保障：本公司有完善的售后服务体系;

公司承诺：

1.购机前，我们专门派技术人员为您设计的流程和方案

2.购机后，将免费指派技术人员为您调试安装

3.整机保修一年，产品终身维护

4.常年供应设备的易损件及耗品确保仪器能长期使用

5、售后管理：我公司实现计算机化管理，实行客户定期电话回访制度，定期复查设备的工作情况，定期电话指导用户对设备进行保养和检测，以便设备正常运转，跟踪客户的设备使用情况，以便及时对设备进行维护

6、物流情况：及时提供货源，确保全国范围内2-10内到货，持续稳定地为代理商做全面服务工作，提供合理的运作空间。公司有专业的技术人员为您安装指导。

7、软件升级：终生免费提供新版本控制软件。

8、安装培训:仪器包装内附有说明书，专业培训人员为客户指定操作者讲解仪器正常操作流程、操作注意事项及仪器的日常维护要求；也可以根据客户要求提供上门培训服务。

Products Description

[Product Name]is a high-quality product designed to meet the needs of businesses looking to[specific goal]. This product offers a range of features and benefits that make it an ideal choice for businesses of all sizes.

Features:

[List key features of the product]

[Include any technical specifications or design details]

Benefits:

[Explain how the product can benefit the customer's business]

[Include specific examples of cost savings, increased productivity, improved efficiency, etc.]

We believe that[Product Name]offers an unbeatable combination of quality, performance, and value. If you have any questions about this product or would like to learn more about how it can benefit your business, please don't hesitate to contact us. We are dedicated to providing excellent customer service and helping our customers achieve their business goals.

Thank you for considering[Product Name]. We look forward to the opportunity to work with you and help you achieve success.

FAQ

1.Q: What is the expected lifespan or durability of the product?

A: Our product has an expected lifespan of X years and is designed to withstand heavy use in industrial environments.

2. Q: What is your company's experience and reputation in the industry?

A: Our company has been in business for X years and has a reputation for delivering high-quality products and excellent customer service. We have worked with numerous clients in various industries.

3. Q: What is your company's policy on returns and refunds?

A: We have a flexible returns and refunds policy that allows customers to return products within X days of purchase for a full refund or exchange. We also offer warranties on our products to ensure customer satisfaction.

4. Q: Are there any certifications or standards that the product meets?

A: Yes, our product meets several industry certifications and standards, including [list certifications and standards].

Product Parameters

Product Name	Model Number	Dimensions

Recommend Products

Other related hot products that may be of interest to you.

List other products from the related categories.

Details Images