产品

10KN电子安全绳拉力拉伸试验机  Software features:

 10KN电子安全绳拉力拉伸试验机

1. Modular functionality of testing standards: Provides users with the ability to set testing standards for their desired applications, covering testing standards and specifications such as GB, ASTM, DIN, JIS, BS, etc.

2. Sample data: Provide users with the ability to set all sample data, input data once for permanent reuse, and modify formulas to improve test data fit.

3. Dual report editing: Fully open for users to edit reports, allowing testers to choose their preferred report format (the test program has added built-in EXCEL report editing functionality, expanding the previous single professional report format).

4. The lengths, force units, and display digits are dynamically interchanged, with force units of T, Kg, N, KN, 5, and lb, and deformation units of mm, cm, and inch.

5. The graph curve scale is automatically optimized by Auto Scale, which can display the graph at the optimal scale and dynamically switch the graph in real-time during testing. It has load displacement, load time, displacement time, stress-strain load-2 point extension diagrams, as well as multi curve comparisons.

6. The test results can be output in the form of WORD and EXCEL data formats.

7. After the test is completed, it can be automatically archived or manually archived. After the test is completed, the maximum strength, upper and lower yield strength, hysteresis loop, stepwise approximation method, non proportional elongation strength, tensile strength, compressive strength, tensile strength at any point, tensile strength at any point, elastic modulus, elongation rate, stripping interval maximum and minimum values, average value, net energy, folding energy, total energy, bending modulus, breakpoint displacement x% load, breakpoint load X% displacement, and so on can be automatically calculated.

8. Data backup: Test data can be saved on any hard drive partition.

9. The software has the function of demonstrating historical tear strength test data.

10. Common testing items: (common display values and calculated values)

● Tensile stress ● Tensile strength

● Tensile strength ● Tensile elongation

● Constant tensile stress ● Constant elongation at constant stress

● Fixed stress value ●

● Force value at any point ● Elongation at any point

● Extraction force ● Adhesive force and peak calculation value

● Pressure test ● Shear peeling force test

● Bending test ● Pull out force puncture force test

11. Special testing items:

A. The elastic coefficient, also known as the Young's modulus of elasticity, is defined as the ratio of the normal stress component to the normal strain in the same phase. To determine the coefficient of material rigidity, the higher the value, the stronger the material.

B. Proportional limit: The load can maintain a proportional relationship with elongation within a certain range, and its maximum stress is the specific limit.

C. Elastic limit: The maximum stress that a material can withstand without permanent deformation.

D. Elastic deformation: After removing the load, the deformation of the material completely disappears.

E. Permanent deformation: After removing the load, the material still retains deformation.

F. Yield point: When a material is stretched, the deformation increases while the stress remains constant, and this point is called the yield point. The yield point is divided into upper and lower yield points, and generally the upper yield point is taken as the yield point. Yield: When the load exceeds the proportional limit and elongation is no longer proportional, the load will suddenly drop, and then fluctuate up and down over a period of time, causing significant changes in elongation. This phenomenon is called yield.

G. Yield strength: The quotient obtained by dividing the load at which the permanent elongation reaches a specified value during stretching by the original cross-sectional area of the parallel part.

H. Spring K value: the ratio of the force component in phase with the deformation to the deformation.

I. Effective elasticity and hysteresis loss:

On a tensile testing machine, when the specimen is stretched at a certain speed to a certain elongation or to a specified load, the percentage of the recovered work during shrinkage and the consumed work during stretching is measured as the effective elasticity; The percentage of the energy lost during the elongation and contraction of a sample compared to the work consumed during elongation is called hysteresis loss.

软件特点:

1、测试标准模块化功能:提供使用者设定所需应用的测试标准设定，范围涵盖GB、ASTM、DIN、JIS、BS…等测试标准规范。

2、试品资料:提供使用者设定所有试品数据，一次输入数据永久重复使用，并可自行增修公式以提高测试数据契合性。
3、 双报表编辑:完全开放式使用者编辑报表，供测试者选择自己喜好的报表格式(测试程序新增内建EXCEL报表编辑功能扩展了以往单一专业报表的格局) 。
4、 各长度、力量单位、显示位数采用动态互换方式，力量单位T、Kg、N、KN、5、lb，变形单位mm、cm、inch。
5、图形曲线尺度自动醉佳化Auto Scale，可使图形以醉佳尺度显示，并可于测试中实时图形动态切换。具有荷重-位移、荷重-时间、位移-时间、应力-应变荷重-2点延伸图，以及多曲线对比。
6、测试结果可以WORD、EXCEL格式的数据形式输出。

7、测试结束可自动存档、手动存档，测试完毕自动求算醉大力量、上、下屈服强度、滞后环法、逐步逼近法、非比例延伸强度、抗拉强度、抗压强度、任意点定伸长强度、任意点定负荷延伸、弹性模量、延伸率、剥离区间醉大值、醉小值、平均值、净能量、折返能量、总能量、弯曲模量、断点位移x％荷重、断点荷重X％位移、等等。
8、数据备份：测试数据可保存在任意硬盘分区。
9、软件具有历史撕裂强度测试数据演示功能。

10、普通测试项目：(普通显示值及计算值)
            ●拉伸应力   ●拉伸强度
            ●扯断强度   ●扯断伸长率
            ●定伸应力   ●定应力伸长率
            ●定应力力值  ●
            ●任意点力值  ●任意点伸长率
            ●抽出力    ●粘合力及取峰值计算值
            ●压力试验   ●剪切力剥离力试验
            ●弯曲试验   ●拔出力穿刺力试验

11、特殊测试项目： 

A.弹性系数即弹性杨氏模量定义：同相位的法向应力分量与法向应变之比。为测定材料刚性之系数，其值越高，材料越强韧。
B.比例限：荷重在一定范围内与伸长可以维持成正比之关系，其醉大应力即为比极限。
C.弹性限：为材料所能承受而不呈永久变形之醉大应力。
D.弹性变形：除去荷重后，材料的变形完全消失。
E.永久变形：除去荷重后，材料仍残留变形。
F.屈服点：材料拉伸时，变形增快而应力不变，此点即为屈服点。屈服点分为上下屈服点，一般以上屈服点作为屈服点。屈服(yield)：荷重超过比例限与伸长不再成正比，荷重会突降，然后在一段时间内，上下起伏，伸长发生较大变化，这种现象叫作屈服。
G.屈服强度：拉伸时，永久伸长率达到某一规定值之荷重，除以平行部原断面积，所得之商。
H.弹簧K值：与变形同相位的作用力分量与形变之比。
I.有效弹性和滞后损失：
在拉力试验机上，以一定的速度将试样拉伸到一定的伸长率或拉伸到规定的负荷时，测定试样收缩时恢复的功和伸张时消耗的功之比的百分数，即为有效弹性；测定试样伸长、收缩时所损失的能与伸长时所消耗的功之比的百分数，即为滞后损失。

常见故障：

1：上升、下降、试验操作时，按下键后显示停止

  解决方案：1：检查系统设置当前量程设置和过载保护率

            2：检查速度参数是否变化

            3：检查传感器是否过载

2：上电后仪表蓝屏

解决方案：1：重新上电

           2：重新上电如果不行，拿到没有干扰的地方上电试一下

           3：联系生产厂家更换液晶屏

3：横梁不移动

 解决方案：1：检查数据线是否连接号

           2：检查是否过载，传感器是否损坏

           3：是否限位，移动磁铁

4：仪表不准确

解决方案：  1：传感器是否损坏

             2：调整了标定系数

             3：是否年检

Common faults:

1: When performing ascending, descending, or experimental operations, pressing the key will display 'stop'

Solution: 1: Check the current range setting and overload protection rate of the system settings

2: Check if the speed parameters have changed

3: Check if the sensor is overloaded

2: Blue screen on the instrument panel after power on

Solution: 1: Power on again

2: If it doesn't work, try powering it on in a place without interference

3: Contact the manufacturer to replace the LCD screen

3: The crossbeam does not move

Solution: 1: Check if the data cable has a connection number

2: Check if there is overload and if the sensor is damaged

3: Is there a limit, move the magnet

4: Inaccurate instrument

Solution: 1: Is the sensor damaged

2: Adjusted the calibration coefficient

3: Is it an annual inspection

关于仪器返厂维修：1、维修维护全面 ：设备损坏后，使用者往往对设备损坏情况描述不清、不全面，经常会出现技术人员到达现场之后，发现工具不全或者零配件需要更换却没有提前准备零配件，常常会造成被动或者维修迟缓的局面，耽误客户使用。设备返厂维修，厂内零配件及工具齐全，技术人员在维修设备同时，按照公司要求会利用厂内设施为返厂的设备做系统的维护，将一些细微的毛病及早解决。2、响应速度快 ：设备损坏后，我们即使以最快的速度为您安排相关的技术人员出差，也要走流程等待技术部门安排具体的人员出差，往往需要一定时间。有时因为技术人员连续出差，耽搁在某地，偶尔还会耽误与客户提前约定好的时间。 现在物流快递行业发达，全国各地运输都很快捷方便，返厂维修往往能更省事省力。

Function Introduction:

After the sample is damaged, the moving crossbeam will automatically stop moving (or return to its initial position)

Automatic shifting automatically switches to the appropriate range based on the magnitude of the test force to ensure the accuracy of the measurement data

The experimental conditions and sample raw data of the conditional module can be stored in the form of their own standard modules; Convenient for users to access and view, saving testing time with automatic transmission

The displacement speed or loading speed during the automatic transmission test process can be automatically completed according to a pre programmed and set program, or manually changed

Automatic saving of the experiment ends, and the experimental data and curves are automatically saved by the computer to prevent data loss caused by forgetting to save them

The testing process, measurement, display, analysis, etc. are all completed by microcomputers

Display method: Data and curves are dynamically displayed during the experimental process

Experimental software with Chinese Windows user interface, easy to operate

The test report can be edited and printed according to user requirements

Batch testing can be completed sequentially for samples with the same parameters after one setting

According to the testing requirements, the automatic process allows users to easily establish their own testing templates (methods, etc.) for easy secondary calling, and can achieve closed-loop testing control of loading speed, stress, and strain

After the completion of the curve traversal experiment, the curve can be enlarged and reanalyzed, and the data corresponding to each point on the experimental curve can be found with the mouse

Users can add test methods according to the test requirements

The limit protection has two levels of programmable and mechanical limit protection

Overload protection automatically shuts down when the load exceeds the rated value by 3-5%

The report displays both automatic and manual modes for obtaining various experimental results, automatically forming reports to simplify the data analysis process and facilitate users

附件：

★一年保固书及中文操作说明书各一份。

★随机赠送标准全拉力试验机夹具一组（其他夹具选购）。

★拉力试验机专用测试软件一份。

★品牌电脑一套、彩色打印机一台(选配)。

6.1.1 观测检查和分辨力的判定

   通过实际试验(或与其他检测试验结合进行)，在试验过程中观测检查5.4.1.1、5.4.1.3和5.4.1.4。

   力指示装置的分辨力r，应在试验机的电动机和控制系统均启动、在零试验力的情况下按5.4.1.2的规定通过观测和计算进行判定。

主要产品有：

拉力试验机，                     塑料球压痕硬度计

维卡热变形试验仪，               体积表面电阻率测试仪

海绵泡沫落球回弹试验机，         海绵泡沫拉伸强度试验机

耐压试验机，                 介电常数测试仪

海绵泡沫压陷硬度测验仪，         介质损耗测试仪

海绵泡沫疲劳压陷试验机，         薄膜冲击试验机

熔融指数仪，                     无转子硫化仪

电压击穿试验仪，                 摩擦系数仪

低温脆性冲击试验仪               阿克隆磨耗试验机等。

公司承诺：

1.购机前，我们专门派技术人员为您设计的流程和方案

2.购机后，将免费指派技术人员为您调试安装

3.整机保修一年，产品终身维护

4.常年供应设备的易损件及耗品确保仪器能长期使用

5、售后管理：我公司实现计算机化管理，实行客户定期电话回访制度，定期复查设备的工作情况，定期电话指导用户对设备进行保养和检测，以便设备正常运转，跟踪客户的设备使用情况，以便及时对设备进行维护

6、物流情况：及时提供货源，确保全国范围内2-10内到货，持续稳定地为代理商做全面服务工作，提供合理的运作空间。公司有专业的技术人员为您安装指导。

7、软件升级：终生免费提供新版本控制软件。

8、安装培训:仪器包装内附有说明书，专业培训人员为客户指定操作者讲解仪器正常操作流程、操作注意事项及仪器的日常维护要求；也可以根据客户要求提供上门培训服务。