产品

注射用水总有机碳分析仪  电源要求

电压：220V ? 22V

电源频率：50Hz ? 1Hz

注射用水总有机碳分析仪 应用领域：

    制药用水（纯化水、注射用水）的在线监测和实验室测试，以及清洁验证；

环保测试、电子行业、食品行业等。

使用与操作方法

开始检测并计入检测次数，检测完毕后显示最后一次检测结果，其中几次检测的结果均自动保存在查询记录当中。检测次数的设置方式为：用“选择”键移动光标，用“设置”键修改数字，按“确定”键进行确认，进入分析界面。先进行四次冲洗过程

在线分析

将TOC 分析仪安置于纯水系统的支管或出水管处，对特定点进行实时、连续、在

线监测。在线检测可方便对水系统的质量进行实时测定并可以对水系统进行实时流程

控制，同时可以在第一时间发现水系统的故障。

运行要求

? 交流电源：170～260 V，频率：50/60 Hz ；

? 分析仪的量程是：电导率< 10.0 us/cm ；TOC < 1.0 PPM 。如果水样中的无

机碳或有机碳浓度超出了仪器的检测范围，需使用高纯水或有机碳浓度较

低的去离子水冲洗管路。

? 仪器运行的环境温度5℃ – 40 ℃。

安全措施忠告：

1．请保证电源可靠接地；

2．电源电缆线的线径 > 2.5 mm2；

3．请勿将仪器浸泡于水或其它液体中。

主要技术参数

A. 基本尺寸：44cm?18cm?26cm

B. 检测极限：0.001mg/L

C. 检测精度：?5%

D. 检测范围：0.001mg/L～1.000mg/L

E. 响应时间：15 min以内

F. 样品温度：1-95℃

G. 电   源：220V?22V

H. 电源频率：50Hz?1Hz

I. 额定功率：100W

J. 分析时间：4min

K. 环境温度：10-40℃    温度变化在?5℃/d以内

L. 内部样品流速：0.5 ml/min

M. 相对湿度：≤ 85%

N. 重复性误差：≤ 3%

O. 零点漂移：?5%

P. 量程漂移：?5%

工作原理

本仪器采用紫外氧化的原理，将样品中的有机物氧化为二氧化碳，二氧化碳的测试采用的是直接电导率法，通过测试经过氧化反应的样品的总碳含量和未经过氧化反应的样品总无机碳的含量差值来测定总有机碳含量，即：总有机碳（TOC）=总碳（TC）-总无机碳（TIC）。

应用范围

该仪器可用于检测制药工业中纯化水、注射用水和去离子水中有机碳的浓度；也可用于半导体行业中超纯水TOC的检测。

在制药领域和生物化学领域清洁验证过程中，可用于验证清洁效果。

该仪器具有在线检测功能，可以在线监测制药工业的制水系统、半导体工业的超纯水制备系统和晶片工艺过程、电厂去离子水制备过程等。

仪器各部件的安装、连接

开箱后，按以下步骤进行安装：

── 根据装箱单检查仪器是否齐备。

── 确定仪器在运输过程中没有遭到损坏。

── 拆除机箱的外包装，将其置于正确位置 。

── 检查仪器保险丝是否装好，连接市电电缆到接线端子。

── 根据安装图连接进液和出液管路 。

── 系统通电 。

产品特点

1.仪器采用便携设计，使用轻便，方便移动至取样点。

2.采用嵌入式系统，触摸屏设计，纯中文操作方便简易。

3.针对制药用水（TOC含量在1000ppb以下）总有机碳含量的检测设计，进行检测。

4.配备大量的储存空间，能够存储大量的测试数据。

5.中文打印，输出测试参数、测试结果。

6.在使用、贮存和更换过程中不需要气体或试剂，无移动部件，减少维修和维护成本。

7.当测试样品浓度超过规定限度，仪器能够自动报警，并输出控制信号。

8.符合国家2010版《中国药典》规定的测试方案，可以提供IQ/OQ/PQ服务。

Power requirements

Voltage: 220V?22V

Power frequency: 50Hz?1Hz

Application field:

Online monitoring and laboratory testing of pharmaceutical water (purified water, injection water), as well as cleaning validation;

Environmental testing, electronics industry, food industry, etc.

Usage and operation methods

Start the detection and count the number of detections. After the detection is completed, the last detection result will be displayed, and the results of several detections will be automatically saved in the query record. The way to set the number of detections is to use the "Select" key to move the cursor, use the "Set" key to modify the number, press the "OK" key to confirm, and enter the analysis interface. Perform four flushing processes first

Online analysis

Place the TOC analyzer at the branch or outlet pipe of the pure water system, and perform real-time, continuous, and accurate monitoring of specific points

Line monitoring. Online detection facilitates real-time measurement of the quality of the water system and enables real-time flow control of the water system

Control, and at the same time, detect faults in the water system as soon as possible.

Operational requirements

AC power supply: 170-260 V, frequency: 50/60 Hz;

The range of the analyzer is: conductivity<10.0 us/cm; TOC<1.0 PPM. If there is none in the water sample

The concentration of organic carbon or organic carbon exceeds the detection range of the instrument, and high-purity water or organic carbon concentration should be used

Flush the pipeline with low deionized water.

The ambient temperature for instrument operation is 5℃-40℃.

Safety measures and advice:

1. Please ensure reliable grounding of the power supply;

2. The wire diameter of the power cable is>2.5 mm2;

3. Do not immerse the instrument in water or other liquids.

Main technical parameters

A. Basic size: 44cm?18cm?26cm

B. Detection limit: 0.001mg/L

C. Detection accuracy:?5%

D. Detection range: 0.001mg/L~1.000mg/L

E. Response time: Within 15 minutes

F. Sample temperature: 1-95℃

G. Power supply: 220V?22V

H. Power frequency: 50Hz?1Hz

I. Rated power: 100W

J. Analysis time: 4 minutes

K. Environmental temperature: 10-40℃Temperature variation within?5℃/d

L. Internal sample flow rate: 0.5 ml/min

M. Relative humidity:≤85%

N. Repeatability error:≤3%

O. Zero drift:?5%

P. Range drift:?5%

operational principle

This instrument adopts the principle of ultraviolet oxidation to oxidize organic matter in the sample to carbon dioxide. The measurement of carbon dioxide is carried out using the direct conductivity method. The total organic carbon content is determined by measuring the difference between the total carbon content of the sample that has undergone oxidation reaction and the total inorganic carbon content of the sample that has not undergone oxidation reaction. That is, total organic carbon (TOC)=total carbon (TC) - total inorganic carbon (TIC).

Application scope

This instrument can be used to detect the concentration of organic carbon in purified water, injection water, and deionized water in the pharmaceutical industry; It can also be used for the detection of TOC in ultrapure water in the semiconductor industry.

In the cleaning validation process in the pharmaceutical and biochemical fields, it can be used to verify the cleaning effect.

This instrument has an online detection function, which can monitor the water preparation system in the pharmaceutical industry, the ultra pure water preparation system and chip process in the semiconductor industry, and the deionized water preparation process in power plants online.

Installation and connection of various components of the instrument

After unpacking, follow the following steps for installation:

Check if the instruments are complete according to the packing list.

Ensure that the instrument has not been damaged during transportation.

Remove the outer packaging of the chassis and place it in the correct position.

Check if the instrument fuse is installed properly and connect the mains cable to the wiring terminal.

Connect the inlet and outlet pipelines according to the installation diagram.

Power on the system.

Product features

1. The instrument adopts a portable design, which is lightweight and easy to move to the sampling point.

2. Adopting embedded system and touch screen design, pure Chinese operation is convenient and simple.

3. Design and conduct testing for the total organic carbon content of pharmaceutical water (TOC content below 1000ppb).

4. Equipped with a large amount of storage space, capable of storing a large amount of test data.

5. Print in Chinese, output test parameters and test results.

6. No gas or reagents are required during use, storage, and replacement, and there are no moving parts, reducing repair and maintenance costs.

When the concentration of the test sample exceeds the specified limit, the instrument can automatically alarm and output a control signal.

8. According to the testing plan specified in the 2010 edition of the Chinese Pharmacopoeia, IQ/OQ/PQ services can be provided.